Skip to content

String wound vs pleated filter cartridges: how to choose

Short answer

Choose a string wound filter cartridge for heavy sediment, viscous liquids and, in glass fibre, high temperatures: it holds dirt through a thick wound wall. Choose a pleated cartridge for a tight or absolute rating and a low pressure drop: it stops particles at the face of a large folded media area. Many systems use both, a wound or melt blown pre-filter ahead of a pleated final filter.

Last updated 20 Nov 20266 min read

How each one filters

A string wound filter cartridge is yarn wound onto a perforated core, looser outside and tighter toward the core. Liquid passes through the full thickness of the winding, and particles are caught at different depths: coarse ones near the outside, finer ones further in. It is a depth filter.

A pleated filter cartridge is a thin sheet of media, folded into pleats around a core. Particles are stopped at the face of the media. The pleats put a large area into the cartridge, so the liquid moves slowly through each square metre and the pressure drop stays low. It is a surface filter.

String wound vs pleated: side by side

  • Where dirt is held. String wound: through the depth of the wall. Pleated: at the media surface, across a large area.
  • Rating basis. String wound filter cartridges are usually rated nominal. Pleated cartridges are made with nominal or absolute ratings, and membrane pleats reach sterilizing grade.
  • Heavy or mixed sediment. String wound copes well: the gradient spreads the load through the wall. A pleated filter cartridge on the same stream can blind quickly at its surface.
  • Pressure drop. Pleated starts lower for the same rating and size, because of its area. A wound filter cartridge rises more slowly as it loads with coarse dirt.
  • Viscous liquids. Wound filter cartridges are often chosen for oils, resins and other thick fluids, where open outer layers help.
  • Temperature. Set by the materials, not the format. Glass fibre yarn on a metal core takes far higher temperatures than polypropylene in either format.
  • Cost. A wound filter cartridge usually costs less per piece. A pleated cartridge can cost less per cubic metre filtered where the dirt load is light and its longer life counts.

Where melt blown fits

A melt blown filter cartridge is also a depth filter: fine polypropylene fibres blown into a tube, denser toward the core. Next to a wound cartridge it has a finer, more even fibre structure and is the common choice for water and RO pre-filtration. A wound cartridge takes heavier sediment, viscous fluids and, in glass fibre, heat. Both are nominal; neither replaces a pleated final filter where an absolute rating is needed.

Searches for "string wound vs polypropylene" usually mean string wound against melt blown polypropylene. String wound filter cartridges are themselves often wound from polypropylene yarn; the difference is the structure, not the polymer.

Using them together: pre-filter and final filter

Where the final filter must be fine, put a depth filter cartridge in front of it. The wound or melt blown pre-filter takes the coarse load at a low cost per change; the pleated final filter sees only what is left, and lasts. If final filters load in days rather than weeks, the pre-filter is usually too open or missing.

Final membranes loading early is a field problem with its own page. Premature membrane blinding

How to choose

  1. Know what must be removed. The particle size that matters to the process downstream, and whether it must be stated nominal or absolute.
  2. Check the fluid and temperature. Choose yarn, media and core that the liquid will not attack at its operating temperature.
  3. Estimate the dirt load. Heavy or variable sediment points to depth filtration first; a light load lets a pleated filter cartridge run long.
  4. Decide the train. One stage where the load is light and the rating loose; a depth pre-filter and a pleated final filter where the rating is tight.
  5. Compare cost per cubic metre filtered. Price per filter cartridge, multiplied by change-outs per year, plus the labour and downtime of each change. The cheaper cartridge is not always the cheaper filtration.

Gopani lines by duty

Start from the duty, not the product name. Each line links to its page; the figures are its own, from its catalogue.

Heavy sediment, general process liquids
Clarywound Extreme
  • Rating 0.5 to 150 µm
  • Change-out 2.5 bar
  • Lengths 9.75" to 70"
Heavy dirt loads where change-outs are the cost
Clarywound 3X
  • Rating 1, 5 µm
  • Max temp 70 °C
  • Change-out 1.4 bar
Water and RO pre-filtration in melt blown
RO Protect Eco
  • Rating 1 to 25 µm
  • Max temp 80 °C
  • Change-out 1.4 bar
Fine or absolute final filtration in polypropylene
Clarypleat HE
  • Rating 0.22 to 50 µm
  • Max temp 80 °C
  • Change-out 2.4 bar
Sterilizing-grade final filtration of aqueous liquids
Clarypleat PES
  • Rating 0.1 to 1 µm
  • Retention ≥ 10⁷ per cm²
  • SIP 30 cycles at 134 °C

Temperatures are maxima for the stated media and core.

Change-out pressure is a recommendation; confirm against your fluid and temperature.

Supplied non-sterile unless otherwise specified.

Replacing a cartridge you already use?

Gopani makes replacement cartridges to a part number, a sample or a drawing. Give the make and the part number you run today, or what the end cap or nameplate shows, with the micron rating and the fluid. An application engineer will reply with the cartridge we would supply for your housing and duty, or ask for what is missing.

Replacement filter cartridges, every familyHigh flow replacement finder

Send the make and part number

The filter cartridge you use today

Or what the end cap or nameplate shows. Have a photograph? Say so here and we will ask for it by email.

Where to reply

By sending this you agree to our Privacy notice.

Frequently asked questions

Is a string wound or a pleated filter better for water?

It depends on the water and the job. For raw water with sediment, a string wound or melt blown depth filter cartridge takes the load at low cost. For a tight or absolute rating, or a final filter before membranes, a pleated cartridge is the right tool. Many water systems use a depth cartridge first and a pleated one after it.

What is the difference between a string wound and a pleated filter cartridge?

A string wound filter cartridge is a depth filter: wound yarn holds particles through its thickness, usually to a nominal rating. A pleated cartridge is a surface filter: folded media stops particles at its face, gives a lower pressure drop, and is made with nominal or absolute ratings.

What is a rope type water filter?

A string wound filter cartridge. The wound yarn looks like rope, which is where the name comes from.

String wound vs polypropylene filter: what is the difference?

Usually the comparison is with melt blown polypropylene. Both are depth filters; melt blown has a finer, more even fibre structure, and string wound takes heavier sediment and, in glass fibre, higher temperatures. String wound filter cartridges are often polypropylene too.

Can I use a pleated cartridge in place of a string wound cartridge?

Where the housing takes the same length and end fitting, yes, and it may run longer on a light load. On heavy sediment it can blind quickly; keep a depth pre-filter in front of it.

Ask an application engineer

Describe your fluid and duty

Deciding between depth and pleated for your liquid? Describe the fluid and the duty. An application engineer will answer by email.

Your fluid and duty

What you are filtering, and what you want to know.

Where to reply

By sending this you agree to our Privacy notice.

Catalogues

Request a catalogue

Each catalogue holds the full specification, dimensions and ordering codes. Catalogues are sent by email on request.

Send us what you run today.

The fluid, the flow, the temperature and the filter cartridge or bag you use now. An application engineer will reply.

Request a quote

Request a catalogue

Tell us who you are and where to send it. Our team emails the catalogue to you.

By sending this you agree to our Privacy notice.