Housings and systems
Plastofilt CFis a polypropylene housing for one 10" or 20" cartridge. Up to 8 m³/hr in the 20" Jumbo.
An injection moulded virgin polypropylene housing for one 10" or 20" cartridge. Slim takes 2.5" OD cartridges and Jumbo takes 4.5" OD, on BSP (F) threaded ports from 1/2" to 1.5". Every housing is inspected and pressure leak tested before delivery.

Up to 8 m³/hr
Plastofilt CF Slim or Jumbo, 10" or 20"
- Flow, 20" Jumbo
- Up to 8 m³/hr
- Maximum operating pressure
- 8 bar at 21 °C
- Temperature
- 4 to 70 °C
- Cartridge OD
- 2.5" or 4.5"
Leak tested before delivery
Every housing goes through a series of inspections and a pressure leak test before it is delivered.
Jumbo for higher flow
A 4.5" OD cartridge takes the flow to up to 8 m³/hr in one 20" housing, so fewer housings are needed.
Knife edge sealing
A knife edge seats the cartridge. The ZeroLeak end is available on 4.5" OD cartridges.
Four seal elastomers
Silicone, FKM, Buna-N or EPDM, chosen for the fluid.
How it is built
Construction
- Automated injection moulding
Sump and top are injection moulded in virgin polypropylene.
- Knife edge seal
The cartridge seats on a knife edge; Jumbo housings take DOE or ZeroLeak cartridges.
- Vent and mounting
An air release vent with a stainless steel spring and screw, and four mounting holes on the top.

| Body | Virgin polypropylene |
|---|---|
| Ports | BSP (F), 1/2" to 1.5" |
| Seal | Silicone, FKM, Buna-N, EPDM |
Specifications
Specification table
MaterialsBody, vent, seals
| Property | Value |
|---|---|
| Housing sump and top | Polypropylene, virgin, injection moulded |
| Vent | Polypropylene with stainless steel spring and screw |
| O-ring / gasket | Silicone, FKM, Buna-N, EPDM |
Operating limitsFlow, pressure, temperature
| Property | Value |
|---|---|
| Flow, 10" Slim | Up to 1 m³/hr |
| Flow, 20" Slim | Up to 2 m³/hr |
| Flow, 10" Jumbo | Up to 4 m³/hr |
| Flow, 20" Jumbo | Up to 8 m³/hr |
| Maximum operating pressure | 0.8 MPa (8.0 bar) at 21 °C |
| Temperature | 4 °C to 70 °C |
SizesCartridge, ports, dimensions A, B, C in mm
| Property | Value |
|---|---|
| 10" Slim | 2.5" OD cartridge, DOE; 1/2", 3/4" or 1" ports; A 312, B 288, C 130 |
| 20" Slim | 2.5" OD cartridge, DOE; 1/2", 3/4" or 1" ports; A 566, B 542, C 130 |
| 10" Jumbo | 4.5" OD cartridge, DOE or ZeroLeak; 1" or 1.5" ports; A 352, B 310, C 180 |
| 20" Jumbo | 4.5" OD cartridge, DOE or ZeroLeak; 1" or 1.5" ports; A 616, B 574, C 180 |
| Box pack | 10 per box 10" Slim; 6 per box 20" Slim; 6 per box 10" Jumbo; 4 per box 20" Jumbo |
Ordering codeBuild the part number field by field
| Property | Value |
|---|---|
| Pattern | PPCF- + size + diameter + cartridge type + connection + body material + seal |
| Size | 10 = 10"; 20 = 20" |
| Diameter | S = Slim; J = Jumbo |
| Cartridge type | 0 = DOE; Z = ZeroLeak |
| Connection | 12 = 1/2"; 34 = 3/4"; 01 = 1"; 15 = 1.5" |
| Body material | P = polypropylene |
| Seal | B = Buna-N; E = EPDM; S = silicone; V = FKM |
Source: Plastofilt CF and BF catalogue, 2026, p3, p5 and p6. Dimensions in mm, ± 2 mm.
Where it runs
Water treatment, RO protection and process liquids
Water treatment and utility water; RO protection and pre-filtration; process water, chemical and industrial liquid filtration; food and beverage water.
2.5" OD cartridges in the Slim; 4.5" OD in the Jumbo, with DOE or ZeroLeak ends. Send us the cartridge you run and we confirm the fit.

“Each housing goes through a series of inspections and a pressure leak test before delivery.”
Resources for this line
Datasheets and catalogue pages that cover Plastofilt CF, as PDF.
- Plastofilt CF and BF1.2 MB · Jun 2026Download
Related products and tools
Above 70 °C
Clary-T Vent is rated to 135 °C.
View Clary-T VentChemical compatibility
A fluid checked against membrane, media, seal and housing materials at the operating temperature.
Open checker
Request a quote
Send the part number you use today, the micron rating, flow and fluid. An application engineer replies with the matching Gopani cartridge.
Request a quote- Download the catalogues
The Plastofilt CF catalogue and the rest of the housings and systems range, as PDF.
Go to downloads - Compare the housings and systems range
Clary-T CF, Clary-T SF sanitary housing, Clary-T SF strainer, Clary-T HF, Clary-T Vent, Clary-T BF, Clary-T LF, ClarySEA FRP housing, Polyfilt CF, Polyfilt BF, Polyfilt HF, Plastofilt BF, Catalyst recovery systems
Open the family