Pleated cartridges
Clarypleat PTFEis a hydrophobic PTFE cartridge for air, gas, vents and solvents. 50 SCFM at 70 mbar in vent mode.
A hydrophobic, chemically inert PTFE membrane on polypropylene support and hardware, for air and gas sterilization, fermentor and tank venting, and API bulk and solvent filtration. Integrity testable by bubble point, diffusion or forward flow, and water intrusion.

0.1 to 5 µm
Clarypleat PTFE OD 69 mm, 5" to 30"
- Vent air flow
- 50 SCFM at 70 mbar
- Liquid challenge
- TR > 10¹¹
- Minimum bubble point
- ≥ 1.0 bar, 60% IPA
- Steam in place
- 100 cycles at 124 °C
Vent flow
50 SCFM at 70 mbar ΔP in vent mode.
Integrity testable
By bubble point, diffusion or forward flow, and water intrusion.
Steam in place
100 SIP cycles at 124 °C or 40 SIP cycles at 140 °C, 30 minutes each, at 0.3 bar ΔP.
Hardware options
Polypropylene as standard; PFA or glass reinforced polypropylene hardware by ordering code.
How it is built
Construction
- Hydrophobic PTFE membrane
Chemically inert PTFE that repels water, for air, gas and vent service.
- Polypropylene support and hardware
PP support, cage, core and end caps as standard; PFA or PP with glass fibre by ordering code.
- Thermally sealed
Sealed without adhesives; each filter is integrity tested and traceable by serial number.

| Membrane | Hydrophobic PTFE |
|---|---|
| Hardware | PP; PFA or PPR by code |
| O-ring | Silicone, EPDM, FEP encapsulated silicone |
Specifications
Specification table
MaterialsMembrane, support, hardware
| Property | Value |
|---|---|
| Membrane | Hydrophobic PTFE (polytetrafluoroethylene) |
| Support layer | Polypropylene |
| Cage, core, end caps, adapters | Polypropylene; PFA and reinforced PP (PP + GF) by ordering code |
| O-ring | Silicone, EPDM, FEP encapsulated silicone |
| Sealing | Thermal sealing, no adhesives |
IntegrityPer 10" cartridge
| Property | Value |
|---|---|
| Minimum bubble point at 25 °C | ≥ 1.0 bar, wetting liquid 60% IPA : water (v/v) |
| Maximum air diffusion at 25 °C | ≤ 20 ml at 0.8 bar, per 10" |
| Bacterial retention, 0.2 µm | ≥ 10⁷ Brevundimonas diminuta per cm² (ASTM F838) |
| Bacterial retention, 0.45 µm | ≥ 10⁷ Serratia marcescens per cm² |
| Liquid challenge | TR > 10¹¹ |
Operating limitsTemperature, pressure, flow, steam
| Property | Value |
|---|---|
| Maximum operating temperature | 80 °C continuous |
| Maximum differential pressure | 5.2 bar forward, 2.1 bar reverse, at 25 °C |
| Water flow | 22 L/min at 0.2 bar, 25 °C |
| Air flow, vent mode | 50 SCFM at 70 mbar ΔP |
| Steam in place, at 0.3 bar ΔP | 40 cycles at 140 °C (30 min); 100 cycles at 124 °C (30 min) |
DimensionsLengths and area
| Property | Value |
|---|---|
| OD | 69 mm |
| Lengths | 5", 10", 15", 20", 30" |
| Effective filtration area, nominal | 0.37, 0.74, 1.0, 1.58, 2.32 m² |
Quality assuranceAs printed in the catalogue
| Property | Value |
|---|---|
| Bacterial endotoxin | ≤ 0.25 EU/ml, LAL test |
| Cytotoxicity and biological reactivity | Meets USP <87> and <88>, Class VI |
| Extractables | Evaluated per USP <661>; with WFI < 40 mg per 10" after autoclaving |
| Particulate matter | Evaluated per USP <788> |
| Fibre release | Meets 21 CFR 210.3(b)(6) |
| Flushed water | TOC ≤ 0.5 mg/l (USP <643>); conductivity ≤ 5.1 µS/cm (USP <645>) |
| Indirect food additives | 21 CFR 177, (EU) No. 1935/2004, (EU) No. 10/2011 |
| Manufacturing facility | ISO 9001, ISO 14001 and ISO 45001 certified (Integrated Management System) |
Ordering codeBuild the part number field by field
| Property | Value |
|---|---|
| Pattern | CPPTFE- followed by micron, length, diameter, end fitting, hardware and seal codes |
| Micron | X = 0.1 µm; A = 0.2 µm; B = 0.45 µm; D = 1 µm; G = 5 µm |
| Length | 05, 10, 15, 20, 30 (inches) |
| Diameter | S = 69 mm |
| End fitting | 1 = Fin / 226; 2 = Fin / 222; 3 = Flat / 226; 4 = Flat / 222 |
| Hardware | PP = polypropylene; PFA = perfluoroalkoxy; PPR = reinforced PP (PP + GF) |
| Seal | B = Buna-N; E = EPDM; S = silicone; V = Viton; W = FEP encapsulated silicone |
Source: Clarypleat PTFE catalogue, edition 10 Aug 2026, PDF pages 2 to 5. Specification table on page 4. Supplied non-sterile unless otherwise specified.
Where it runs
Air and gas, tank and fermentor vents, and solvent filtration
Air and gas filtration in pharma, biopharma and food and beverage; fermentor venting and breathing filters; WFI, HPW and UPW tank vents.
Solvent filtration, aggressive product filtration, and fine and bulk chemical filtration.

“Fully integrity testable by bubble point, diffusion or forward flow, and water intrusion.”
Questions
Clarypleat PTFE: common questions
- How is a hydrophobic PTFE cartridge integrity tested?
- The catalogue gives a minimum bubble point of ≥ 1.0 bar with 60% IPA : water and a maximum diffusion of ≤ 20 ml at 0.8 bar per 10", and states the cartridge can be tested by bubble point, diffusion or forward flow, and water intrusion.
- Is PFA hardware available?
- Yes. Hardware code PFA (perfluoroalkoxy) is listed alongside PP and PPR (PP with glass fibre).
Resources for this line
Datasheets and catalogue pages that cover Clarypleat PTFE, as PDF.
Related products and tools
Above 80 °C
Kryticalpleat All Fluoropolymer is rated to 160 °C.
View Kryticalpleat All FluoropolymerChemical compatibility
A fluid checked against membrane, media, seal and housing materials at the operating temperature.
Open checkerHousings
Stainless steel, uPVC, FRP and polypropylene housings, bag vessels and skids.
View housings and systems
Request a quote
Send the part number you use today, the micron rating, flow and fluid. An application engineer replies with the matching Gopani cartridge.
Request a quote- Download the catalogues
The Clarypleat PTFE catalogue and the rest of the pleated cartridges range, as PDF.
Go to downloads - Compare the pleated cartridges range
Kryticalpleat PES, Kryticalpleat All Fluoropolymer, Clarypleat PES, Clarypleat HE, Clarypleat NE, Clarypleat CPU, Clarypleat PVDF, Clarypleat Nylon, Clarypleat 5000
Open the family