Skip to content

String wound

Clarywound 3Xis an all-polypropylene string wound cartridge with a multilayered gradient. 1 and 5 µm.

Polypropylene yarn wound under CNC control onto a polypropylene core, layer by layer, to build a multilayered micronic gradient. The catalogue rates it at 3 times the dirt holding capacity of a conventional string wound cartridge.

Group of Clarywound 3X wound cartridges, shown at a diagonal

1 and 5 µm

Clarywound 3X OD 63 mm, ID 27.5 mm, 10" to 40"

Clarywound 3XRequest a quote
Retention rating
1, 5 µm
Dirt holding
3 times a conventional string wound cartridge
Maximum operating temperature
70 °C
Recommended change‑out ΔP
1.4 bar at 21 °C
  • Dirt holding

    Rated at 3 times the dirt holding capacity of a conventional string wound cartridge, which means fewer change-outs for the same load.

  • Multilayered gradient

    Each layer is wound tighter toward the core, so coarse particles stop in the outer layers and finer ones further in.

  • All polypropylene

    Media, core and end caps in polypropylene. No resin binders, lubricants, antistatic or release agents are used.

  • End fittings and seals

    Eight end fittings and five seal options in the ordering code. The catalogue states that other fitments can be made to suit.

How it is built

Construction

  1. CNC winding

    Polypropylene yarn is wound onto the core layer by layer under CNC control.

  2. Multilayered micronic gradient

    The winding tightens toward the core, so dirt loads through the full depth of the wall.

  3. No additives

    Gopani certifies that no resin binders, lubricants, antistatic or release agents are used in manufacture.

Group of Clarywound 3X wound cartridges, shown at a diagonal
MediaPolypropylene
Core and end capsPolypropylene
SealNone, Buna-N, EPDM, silicone, FKM

Specifications

Specification table

MaterialsMedia, core, end caps

PropertyValue
Filter mediaPolypropylene
Core and end capsPolypropylene

PerformanceRetention, dirt holding, pressure

PropertyValue
Retention rating1, 5 µm
Dirt holding3 times a conventional string wound cartridge
Maximum operating temperature70 °C (158 °F), polypropylene with polypropylene
Recommended change-out ΔP0.14 MPa (1.4 bar; 20.3 psid) at 21 °C
Surface area≥ 0.52 ft² per 10" cartridge length

DimensionsDiameter and lengths

PropertyValue
OD / ID63 ± 0.5 mm / 27.5 ± 0.5 mm
Lengths10", 20", 30", 40"
PackingMultiples of 5

Ordering codeBuild the part number field by field

PropertyValue
PatternCW3X- followed by micron, length, diameter, end fitting, material, hardware and seal codes
MicronD = 1 µm; G = 5 µm
Length10, 20, 30, 40 (inches)
DiameterS = 63 mm
End fitting0 = None (DOE without end cap); 1 = Fin / 226, Code-7 with fin; 2 = Fin / 222 T1, SOE T1 (45 mm) with fin; 3 = Flat / 226, Code-7 flat end; 4 = Flat / 222 T1, SOE T1 (45 mm) flat; 5 = DOE (with end cap); 6 = Fin / 222 T2, SOE T2 (47 mm) with fin; 7 = Flat / 222 T2, SOE T2 (47 mm) flat
MaterialPP = polypropylene
HardwarePP = polypropylene
SealX = none; B = Buna-N; E = EPDM; S = silicone; V = FKM

Source: Clarywound 3X catalogue, 2026, pages 2 to 4. The 3X dirt holding figure is stated against a conventional string wound cartridge.

Where it runs

Where it is used

Duty

Water and process liquids at up to 70 °C where a polypropylene wound cartridge is suitable and the aim is to change cartridges less often.

Sizing

Send the flow, the fluid and the housing, and an application engineer sizes the cartridge count and length.

“Manufactured by proprietary CNC machining process to construct a true multilayered micronic gradient.”
Clarywound 3X catalogue, 2026, page 2
See the catalogues

Resources for this line

Datasheets and catalogue pages that cover Clarywound 3X, as PDF.

Open the full library

Related products and tools

  • Above 70 °C

    Clarywound GF is rated to 350 °C.

    View Clarywound GF
  • Finer ratings

    Clarywound Extreme is available from 0.5 µm (0.5 to 150 µm).

    View Clarywound Extreme
  • Chemical compatibility

    A fluid checked against membrane, media, seal and housing materials at the operating temperature.

    Open checker
  • Housings

    Stainless steel, uPVC, FRP and polypropylene housings, bag vessels and skids.

    View housings and systems

Request a quote

Send the part number you use today, the micron rating, flow and fluid. An application engineer replies with the matching Gopani cartridge.

Request a quote
  • Download the catalogues

    The Clarywound 3X catalogue and the rest of the string wound range, as PDF.

    Go to downloads
  • Compare the string wound range

    Clarywound Extreme, Clarywound Ultra, Clarywound Extreme Bico, Clarywound CPU, Clarywound GF

    Open the family

Download a catalogue

Tell us who you are once and every catalogue opens.

By sending this you agree to our Privacy notice.