String wound
Clarywound Extremeis a CNC wound depth cartridge in polypropylene, cotton or glass fibre. 0.5 to 150 µm.
A gradient depth cartridge, wound denser from the outer layers to the inner. Polypropylene, cotton or glass fibre media, with nylon, rayon, polyester and other yarns on request, on a polypropylene, glass filled polypropylene, stainless steel or tinned steel core. The maximum temperature is set by the media and core.

0.5 to 150 µm
Clarywound Extreme OD 61, 63 or 110 mm, 9.75" to 70"
- Retention rating
- 0.5 to 150 µm
- Maximum temperature, by media and core
- 80 to 350 °C
- Recommended change‑out ΔP
- 2.5 bar at 21 °C
- Lengths
- 9.75" to 70"
Media and temperature
80 °C in polypropylene on a polypropylene core; 120 °C in cotton, 121 °C in polyester, 140 °C in nylon or rayon and 350 °C in glass fibre, each on a stainless steel core.
Retention range
Nine ratings from 0.5 to 150 µm.
End fittings
Eleven end fittings, including Code-7 (226), SOE 222 T1, T2 and T3, DOE and Zeroleak, in eight lengths.
No additives
Gopani certifies that no resin binders, lubricants, antistatic or release agents are used in manufacture.
How it is built
Construction
- CNC winding
The yarn is wound onto the core under CNC control to build a gradient depth filter.
- Progressive density
Density rises from the outer to the inner layers, so contaminant is held across the full depth.
- Media and core
Polypropylene on a polypropylene core for water and general service; cotton, polyester, nylon, rayon or glass fibre on a stainless steel core for higher temperatures.

| Media | PP, cotton, glass fibre |
|---|---|
| Core | PP, glass filled PP, SS, tinned steel |
| Seal | Silicone, FKM, Buna-N, EPDM |
Specifications
Specification table
MaterialsMedia, core, end caps, seals
| Property | Value |
|---|---|
| Filter media | Polypropylene, cotton, glass fibre. Nylon, rayon, polyester and other yarn types on request |
| Core | Polypropylene, glass filled polypropylene, SS 304 / 304L / 316 / 316L, tinned steel. Other types on request |
| End caps | Polypropylene |
| O-ring / gasket | Silicone, FKM, Buna-N, EPDM |
TemperatureMaximum, by media and core
| Property | Value |
|---|---|
| Polypropylene with polypropylene core | 80 °C (176 °F) |
| Cotton with SS core | 120 °C (248 °F) |
| Polyester with SS core | 121 °C (248.9 °F) |
| Nylon with SS core | 140 °C (284 °F) |
| Rayon with SS core | 140 °C (284 °F) |
| Glass fibre with SS core | 350 °C (662 °F) |
PerformanceRetention, pressure, area
| Property | Value |
|---|---|
| Retention rating | 0.5, 1, 5, 10, 20, 25, 50, 100, 150 µm |
| Recommended change-out ΔP | 0.25 MPa (2.5 bar; 36.25 psid) at 21 °C |
| Surface area | ≥ 0.52 ft² standard (OD 61 mm), ≥ 0.94 ft² jumbo (OD 110 mm), per 10" cartridge length |
DimensionsDiameters and lengths
| Property | Value |
|---|---|
| OD / ID, standard | 61 ± 0.5 mm / 27.5 ± 0.5 mm |
| OD / ID, 63 mm | 63 ± 0.5 mm / 27.5 ± 0.5 mm |
| OD / ID, jumbo | 110 ± 0.5 mm / 27.5 ± 0.5 mm |
| Lengths | 9.75", 10", 20", 30", 40", 50", 60", 70" |
| Other OD and lengths | On request |
Ordering codeBuild the part number field by field
| Property | Value |
|---|---|
| Pattern | CWE- followed by micron, length, diameter, end fitting, material, core and seal codes |
| Micron | C = 0.5 µm; D = 1 µm; G = 5 µm; H = 10 µm; I = 20 µm; J = 25 µm; L = 50 µm; M = 100 µm; N = 150 µm |
| Length | 09 = 9.75"; 10, 20, 30, 40, 50, 60, 70 (inches) |
| Diameter | S = 61 mm; P = 63 mm; J = 110 mm |
| End fitting | 0 = None (DOE without end cap); 1 = Fin / 226, Code-7 with fin; 2 = Fin / 222 T1, SOE T1 (45 mm) with fin; 3 = Flat / 226, Code-7 flat end; 4 = Flat / 222 T1, SOE T1 (45 mm) flat; 5 = DOE (with end cap); 6 = Fin / 222 T2, SOE T2 (47 mm) with fin; 7 = Flat / 222 T2, SOE T2 (47 mm) flat; 8 = Fin / 222 T3, SOE T3 (42 mm) with fin; 9 = Flat / 222 T3, SOE T3 (42 mm) flat; 10 = Zeroleak |
| Material | PP = polypropylene; BC = bleached cotton; GF = glass fibre; NY = nylon; PE = polyester |
| Core | PP = polypropylene; GP = glass filled PP; S4 = SS 304; 4L = SS 304L; S6 = SS 316; 6L = SS 316L; TS = tinned steel; S4E, 4LE, S6E, 6LE = SS 304, 304L, 316, 316L extended core |
| Seal | X = none; B = Buna-N; E = EPDM; S = silicone; V = FKM |
Source: Clarywound Extreme catalogue, 2026, pages 2 to 4. Temperatures are maxima for the stated media and core.
Where it runs
Where it is used
Raw water treatment, wastewater treatment, electroplating, power generation, and chemicals and pharmaceuticals.
Polypropylene to 80 °C for water and general service. Cotton, polyester, nylon or rayon on a stainless steel core from 120 to 140 °C. Glass fibre on a stainless steel core to 350 °C.

“Progressive density from outer to inner layers.”
Resources for this line
Datasheets and catalogue pages that cover Clarywound Extreme, as PDF.
Related products and tools
Finer ratings
Clarypleat PVDF is available from 0.45 µm (0.1, 0.22, 0.45 µm).
View Clarypleat PVDFChemical compatibility
A fluid checked against membrane, media, seal and housing materials at the operating temperature.
Open checkerHousings
Stainless steel, uPVC, FRP and polypropylene housings, bag vessels and skids.
View housings and systems
Request a quote
Send the part number you use today, the micron rating, flow and fluid. An application engineer replies with the matching Gopani cartridge.
Request a quote- Download the catalogues
The Clarywound Extreme catalogue and the rest of the string wound range, as PDF.
Go to downloads - Compare the string wound range
Clarywound 3X, Clarywound Ultra, Clarywound Extreme Bico, Clarywound CPU, Clarywound GF
Open the family