Skip to content

Meltblown

RO Protect Extremefilters down to 0.5 µm with no binders in the media. Change-out at 2.4 bar.

A graded depth meltblown polypropylene cartridge for RO pre-filtration, desalination, chemicals and solvents. Gopani certifies that no resin binders, lubricants, antistatic or release agents are used in its manufacture.

RO Protect Extreme, catalogue image

0.5, 1, 5 µm

RO Protect Extreme OD 63 mm, ID 28 mm, 10" to 40"

RO Protect ExtremeRequest a quote
Retention rating
0.5, 1, 5 µm
Maximum operating temperature
80 °C
Recommended change‑out ΔP
2.4 bar at 21 °C
Surface area
≥ 0.52 ft² per 10"
  • Down to 0.5 µm

    Three ratings, 0.5, 1 and 5 µm, for fine particle removal ahead of RO membranes.

  • Nothing added to the media

    Thermally bonded polypropylene fibres with no resin binders, lubricants, antistatic or release agents.

  • Optional grooved surface

    Grooving adds surface area for a lower clean pressure drop and more dirt holding, without changing the open pore structure.

  • Eight end fittings

    Including Code-7 (226) and SOE 222 T1 and T2, with silicone, FKM, Buna-N or EPDM seals.

How it is built

Graded depth, thermally bonded, sealed without adhesives.

  1. Graded depth structure

    Meltblown polypropylene fibres are laid down in a graded depth structure, so particles load through the wall and not only at the surface.

  2. Thermally bonded fibres

    The fibres are bonded by heat alone. No resin binders, lubricants, antistatic or release agents go into the cartridge.

  3. Thermal sealed caps

    End caps are thermal sealed, free of surfactants, binders and adhesives. A grooved surface pattern is optional.

RO Protect Extreme, catalogue image
MediaPolypropylene
End capsPolypropylene
SealSilicone, FKM, Buna-N, EPDM

Specifications

Specification table

MaterialsMedia, end caps, seals

PropertyValue
Filter mediaPolypropylene, thermally bonded
End capsPolypropylene
O-ring / gasketSilicone, FKM, Buna-N, EPDM
Material complianceMaterials of construction conform to U.S. FDA 21 CFR Part 177

PerformanceRetention, temperature, pressure

PropertyValue
Retention rating0.5, 1, 5 µm
Maximum operating temperature80 °C (176 °F)
Recommended change-out ΔP0.24 MPa (2.4 bar; 34.8 psid) at 21 °C
Surface area≥ 0.52 ft² per 10" cartridge length

DimensionsDiameters and lengths

PropertyValue
OD / ID63 ± 0.5 mm / 28 ± 0.5 mm
Lengths10", 20", 30", 40"
Box pack50 per box for 10" standard; 25 per box for 20", 30", 40" standard

Ordering codeBuild the part number field by field

PropertyValue
PatternRPEX- followed by micron, length, diameter, end fitting, material, core, seal
MicronC = 0.5 µm, D = 1 µm, G = 5 µm
Length10, 20, 30, 40 (inches)
DiameterP = 63 / 63.5 mm
End fitting0 = None (DOE without end cap); 1 = Fin / 226, Code-7 with fin; 2 = Fin / 222 T1, SOE T1 (45 mm) with fin; 3 = Flat / 226, Code-7 flat end; 4 = Flat / 222 T1, SOE T1 (45 mm) flat; 5 = DOE (with end cap); 6 = Fin / 222 T2, SOE T2 (47 mm) with fin; 7 = Flat / 222 T2, SOE T2 (47 mm) flat
MaterialPP = polypropylene
CoreX = no core
SealX = none, B = Buna-N, E = EPDM, S = silicone, V = FKM

Source: RO Protect Extreme catalogue, 2026, p2 to p4. Change-out pressure is a recommendation; confirm against your fluid and temperature.

Where it runs

Fine pre-filtration ahead of RO membranes, and for process fluids.

Applications

Pre-RO and desalination systems, industrial water, petrochemical and chemical processing, electronics and precision industries, and slurries, solvents and process fluids.

Supply

Readily available, with a scheduled delivery service to cover an annual requirement.

“No resin binders, lubricants, antistatic or release agents are used.”
RO Protect Extreme catalogue, 2026, p4
See the catalogues

Resources for this line

Datasheets and catalogue pages that cover RO Protect Extreme, as PDF.

  • RO Protect Extreme2.3 MB · Sep 2026
    Download

Open the full library

Related products and tools

  • Above 80 °C

    Fluidizing filters is rated to 600 °C.

    View Fluidizing filters
  • Finer ratings

    Clarypleat PVDF is available from 0.45 µm (0.1, 0.22, 0.45 µm).

    View Clarypleat PVDF
  • Chemical compatibility

    A fluid checked against membrane, media, seal and housing materials at the operating temperature.

    Open checker
  • Housings

    Stainless steel, uPVC, FRP and polypropylene housings, bag vessels and skids.

    View housings and systems

Request a quote

Send the part number you use today, the micron rating, flow and fluid. An application engineer replies with the matching Gopani cartridge.

Request a quote
  • Download the catalogues

    The RO Protect Extreme catalogue and the rest of the meltblown range, as PDF.

    Go to downloads
  • Compare the meltblown range

    RO Protect Prime, RO Protect Eco Plus, RO Protect Eco, RO Protect Ultra, ClaryNira MB

    Open the family

Download a catalogue

Tell us who you are once and every catalogue opens.

By sending this you agree to our Privacy notice.