Skip to content

Pleated cartridges

Clarypleat HEis an all-polypropylene pleated cartridge with no binder in the media. ≥ 0.6 m² of media per 10".

A binder-free polypropylene pleated cartridge for industrial liquids, used as a pre-filter or as a final filter. The media contains no surfactant or binder that can break down, leach out or migrate, and every component is thermally welded. Lengths run from 10" to 70" at 69 mm diameter.

Clarypleat HE pleated cartridges, 10 inch and 30 inch, front view

0.22 to 50 µm

Clarypleat HE OD 69 mm, 10" to 70"

Clarypleat HERequest a quote
Media area
≥ 0.6 m² per 10"
Retention rating
0.22 to 50 µm
Maximum operating temperature
80 °C
Recommended change‑out ΔP
2.4 bar at 21 °C
  • Binder‑free media

    No surfactant or binder in the media, so no channelling or media migration.

  • Media area

    ≥ 0.6 m² per 10" gives high flow at reduced pressure loss and a higher dirt holding capacity.

  • Pre‑filter or final filter

    Ratings from 0.22 to 50 µm, in lengths from 10" to 70".

  • Steam sterilizable

    Autoclave or in situ steam at 121 °C in 30 minute cycles, up to 10 hours accumulated exposure.

How it is built

Construction

  1. High surface area layer

    Pleated polypropylene puts ≥ 0.6 m² of media in every 10" of length.

  2. Gradient density depth structure

    Behind the surface layer, a depth structure of graded density retains particles through the media.

  3. Thermally welded

    All components are sealed by thermal welding; no binder or surfactant is used.

Clarypleat HE pleated cartridges, 10 inch and 30 inch, front view
MediaPolypropylene
Cage, core, end capsPolypropylene
SealSilicone, FKM, Buna-N, EPDM

Specifications

Specification table

MaterialsMedia, hardware, seals

PropertyValue
Filter mediaPolypropylene, binder-free
End caps, cage, corePolypropylene
O-ring / gasketSilicone, FKM, Buna-N, EPDM
Food contactAll components FDA compliant for food contact under CFR Title 21; for aqueous, acidic, alcoholic (up to 50%) and dairy foods at 40 °C under standard flow conditions

PerformanceRetention, temperature, pressure

PropertyValue
Retention rating0.22, 0.45, 1, 5, 10, 20, 50 µm
Media area≥ 0.6 m² per 10" cartridge length
Maximum operating temperature80 °C (176 °F)
Recommended change-out ΔP0.24 MPa (2.4 bar; 34.8 psid) at 21 °C
SteamAutoclave or in situ steam, 121 °C, 30 min cycles, maximum accumulated exposure 10 hours

DimensionsDiameter and lengths

PropertyValue
OD69 mm (2.71")
Lengths10", 20", 30", 40", 50", 60", 70"

Ordering codeBuild the part number field by field

PropertyValue
PatternCPHE- followed by micron, length, diameter, end fitting, hardware and seal codes
MicronA = 0.22 µm; B = 0.45 µm; D = 1 µm; G = 5 µm; H = 10 µm; I = 20 µm; L = 50 µm
Length10, 20, 30, 40, 50, 60, 70 (inches)
DiameterS = 69 mm
End fitting1 = Fin / 226; 2 = Fin / 222; 3 = Flat / 226; 4 = Flat / 222; 5 = DOE (with end cap)
HardwarePP = polypropylene
SealB = Buna-N; E = EPDM; S = silicone; V = FKM

Source: Clarypleat HE catalogue, 2026, PDF pages 2 to 4. Where the earlier Clarypleat HE one-pager differs, the 2026 catalogue applies.

Where it runs

Food and beverage, process water and fine chemicals

Where the catalogue puts it

Food and beverage filtration; RO pre-filtration, deionised water systems and process water; fine and plating chemicals; wastewater treatment.

Ahead of a membrane

As a pre-filter, HE can take the particle load ahead of a Clarypleat PES or PTFE membrane cartridge.

“Clarypleat HE pleated cartridges contain no surfactant or binder that can break down, leach out, or permit the typical problems of channelling and media migration.”
Clarypleat HE one-pager
See the catalogues

Questions

Clarypleat HE: common questions

Can Clarypleat HE be steam sterilized?
Yes. Autoclave or in situ steam at 121 °C, in 30 minute cycles, for a maximum accumulated exposure of 10 hours.
Is it suitable for food contact?
The catalogue states all components are FDA compliant for food contact under CFR Title 21, for aqueous, acidic, alcoholic (up to 50%) and dairy foods at 40 °C under standard flow conditions.

Resources for this line

Datasheets and catalogue pages that cover Clarypleat HE, as PDF.

  • Clarypleat HE0.6 MB · Sep 2026
    Download
  • Beverage filtration11.6 MB · Sep 2026
    Download
  • Food and beverage1.3 MB · Jul 2026
    Download
  • Clarypleat HE and high flow one-pager0.2 MB · Jan 2026
    Download
  • Beer4.1 MB · Nov 2025
    Download
  • Dairy3.6 MB · Nov 2025
    Download

Open the full library

Related products and tools

Request a quote

Send the part number you use today, the micron rating, flow and fluid. An application engineer replies with the matching Gopani cartridge.

Request a quote
  • Download the catalogues

    The Clarypleat HE catalogue and the rest of the pleated cartridges range, as PDF.

    Go to downloads
  • Compare the pleated cartridges range

    Kryticalpleat PES, Kryticalpleat All Fluoropolymer, Clarypleat PES, Clarypleat PTFE, Clarypleat NE, Clarypleat CPU, Clarypleat PVDF, Clarypleat Nylon, Clarypleat 5000

    Open the family

Download a catalogue

Tell us who you are once and every catalogue opens.

By sending this you agree to our Privacy notice.