Pleated cartridges
Clarypleat Nylonis a pleated cartridge with a naturally hydrophilic nylon 6,6 membrane. 0.2 and 0.45 µm, each filter integrity tested.
A symmetric nylon 6,6 membrane on a polyester support layer, hydrophilic without wetting agents, pleated in polypropylene hardware and thermally sealed with no adhesives. Each filter is integrity tested and traceable by serial number.

0.2 and 0.45 µm
Clarypleat Nylon OD 69 mm, 5" to 30"
- Minimum bubble point at 25 °C
- ≥ 2.5 bar
- Maximum operating temperature
- 80 °C continuous
- Maximum forward ΔP
- 5.2 bar at 25 °C
- Effective area, 10"
- 0.62 m²
Naturally hydrophilic
The nylon 6,6 membrane wets without added wetting agents.
Integrity tested
Each filter is integrity tested and traceable by serial number.
No adhesives
Components are joined by thermal sealing.
Steam in place
30 cycles at 134 °C (20 min) or 30 cycles at 124 °C (30 min).
How it is built
How it is built
- Membrane
Symmetric nylon 6,6 membrane with uniform porosity on a polyester support layer.
- Pleat pack
The membrane is pleated with polypropylene cage, core, end caps and adapters.
- Thermal sealing
The cartridge is sealed thermally, with no adhesives, then integrity tested.

| Membrane | Nylon 6,6 |
|---|---|
| Support layer | Polyester |
| Hardware | Polypropylene |
Specifications
Specification table
MaterialsMembrane, support, hardware
| Property | Value |
|---|---|
| Membrane | Nylon 6,6, naturally hydrophilic |
| Support layer | Polyester |
| Cage, core, end caps, adapters | Polypropylene |
| O-ring | Silicone, EPDM |
| Sealing | Thermal sealing, no adhesives |
IntegrityPer 10" cartridge
| Property | Value |
|---|---|
| Minimum bubble point at 25 °C | ≥ 2.5 bar, wetting liquid DI water |
| Maximum air diffusion at 25 °C | ≤ 23 ml at 2.0 bar, per 10" |
| Bacterial retention, 0.2 µm | ≥ 10⁷ Brevundimonas diminuta per cm² (ASTM F838) |
| Bacterial retention, 0.45 µm | ≥ 10⁷ Serratia marcescens per cm² |
| Integrity testing | Each filter; traceable by serial number |
Operating limitsTemperature, pressure, steam
| Property | Value |
|---|---|
| Maximum operating temperature | 80 °C continuous |
| Maximum differential pressure, forward | 5.2 bar at 25 °C |
| Maximum differential pressure, reverse | 2.1 bar at 25 °C |
| Water flow | 13 L/min at 0.2 bar, 25 °C |
| Steam in place | 30 cycles at 134 °C (20 min cycles); 30 cycles at 124 °C (30 min cycles) |
| pH | Stable filtration behaviour across pH 4 to 9 |
DimensionsLengths and area
| Property | Value |
|---|---|
| OD | 69 mm |
| Lengths | 5", 10", 15", 20", 30" |
| Effective filtration area, nominal | 0.31, 0.62, 1.0, 1.24, 1.86 m² |
Quality assuranceAs printed in the catalogue
| Property | Value |
|---|---|
| Bacterial endotoxin | ≤ 0.25 EU/ml, LAL test |
| Cytotoxicity and biological reactivity | Meets USP <87> and <88> |
| Extractables | With WFI < 30 mg per 10" after autoclaving |
| Fibre release | Meets 21 CFR 210.3(b)(6) |
| Flushed water | TOC ≤ 0.5 mg/l; conductivity ≤ 5.1 µS/cm |
| Indirect food additives | 21 CFR 177, (EU) No. 1935/2004, (EU) No. 10/2011 |
Ordering codeBuild the part number field by field
| Property | Value |
|---|---|
| Pattern | CPNY- followed by micron, length, diameter, end fitting, hardware and seal codes |
| Micron | A = 0.2 µm; B = 0.45 µm |
| Length | 05, 10, 15, 20, 30 (inches) |
| Diameter | S = 69 mm |
| End fitting | 1 = Fin / 226; 2 = Fin / 222; 3 = Flat / 226; 4 = Flat / 222 |
| Hardware | PP = polypropylene |
| Seal | E = EPDM; S = silicone; V = Viton |
Source: Clarypleat Nylon catalogue, 2026, PDF pages 2 to 5. Specification table on page 4. Supplied non-sterile unless otherwise specified.
Where it runs
Where it is used
Small volume parenterals, synthetic culture media and buffers.
Ultrapure and high purity water, and membrane filtration of food and beverage products.

“Each filter is integrity tested and traceable by serial number.”
Questions
Clarypleat Nylon: common questions
- Are the filters supplied sterile?
- They are supplied non-sterile unless otherwise specified.
Resources for this line
Datasheets and catalogue pages that cover Clarypleat Nylon, as PDF.
- Clarypleat Nylon0.8 MB · Apr 2026Download
Related products and tools
Above 80 °C
Kryticalpleat All Fluoropolymer is rated to 160 °C.
View Kryticalpleat All FluoropolymerFiner ratings
Clarypleat HE is available from 0.22 µm (0.22 to 50 µm).
View Clarypleat HEChemical compatibility
A fluid checked against membrane, media, seal and housing materials at the operating temperature.
Open checkerHousings
Stainless steel, uPVC, FRP and polypropylene housings, bag vessels and skids.
View housings and systems
Request a quote
Send the part number you use today, the micron rating, flow and fluid. An application engineer replies with the matching Gopani cartridge.
Request a quote- Download the catalogues
The Clarypleat Nylon catalogue and the rest of the pleated cartridges range, as PDF.
Go to downloads - Compare the pleated cartridges range
Kryticalpleat PES, Kryticalpleat All Fluoropolymer, Clarypleat PES, Clarypleat PTFE, Clarypleat HE, Clarypleat NE, Clarypleat CPU, Clarypleat PVDF, Clarypleat 5000
Open the family