Pleated cartridges
Clarypleat CPUis a pleated polypropylene cartridge for condensate polishing, with backwash data. 1, 4 and 10 µm absolute.
All-polypropylene pleated cartridges for condensate polishing units. The pleated design increases filtration area, which lowers pressure drop and reduces change-out frequency. 60" and 70" long at 70 mm OD, with water and gas backwash conditions stated.

1, 4, 10 µm absolute
Clarypleat CPU OD 70 mm, 60" and 70"
- Retention, absolute
- 1, 4, 10 µm
- Flow
- 3.5 to 4.5 m³/hr
- Change‑out ΔP
- 3.0 bar at 65 °C
- Maximum temperature
- 82 °C
Grade by unit size
The catalogue recommends 4 µm 70" elements for 600 MW supercritical units, 1 µm for 1000 MW ultra-supercritical units, and 10 µm during start-up.
Backwash
Water at 0.45 to 0.65 m³/hr, or gas at 3.4 to 5 m³/hr, at 1.36 to 2.1 bar.
Absolute ratings
1, 4 and 10 µm absolute.
Two change‑out points
3.0 bar at 65 °C; 2.0 bar at 20 °C.
How it is built
Construction
- Pleated PP media
Pleated polypropylene at 70 mm OD, 60" or 70" long.
- Service
3.5 to 4.5 m³/hr per cartridge, changed out at 3.0 bar at 65 °C.
- Backwash
Water or gas backwash at 1.36 to 2.1 bar.

| Media | Pleated polypropylene |
|---|---|
| OD / ID | 70 ± 0.5 / 28 ± 0.5 mm |
| Seal | Buna-N |
Specifications
Specification table
SpecificationAs stated
| Property | Value |
|---|---|
| Retention, absolute | 1, 4, 10 µm |
| Media | Pleated polypropylene |
| End caps | Polypropylene |
| O-ring / gasket | Buna-N |
| OD / ID | 70 ± 0.5 mm / 28 ± 0.5 mm |
| Lengths | 60", 70" |
| Flow | 3.5 to 4.5 m³/hr |
| Recommended change-out ΔP | 3.0 bar at 65 °C; 2.0 bar at 20 °C |
| Maximum temperature | 82 °C (179.6 °F) |
| Backwash, water | 0.45 to 0.65 m³/hr at 1.36 to 2.1 bar |
| Backwash, gas | 3.4 to 5 m³/hr at 1.36 to 2.1 bar |
| Recommended grade | 600 MW supercritical: 4 µm, 70"; 1000 MW ultra-supercritical: 1 µm, 70"; start-up: 10 µm |
Ordering codeBuild the part number field by field
| Property | Value |
|---|---|
| Pattern | CPCPU followed by micron, length, diameter, end fitting, material, core and seal codes |
| Micron | A = 1 µm; B = 4 µm; C = 10 µm |
| Length | 60 = 60"; 70 = 70" |
| Diameter | S = 70 mm |
| End fitting | 0 = DOE |
| Material | PP = pleated polypropylene |
| Core | X = no core |
| Seal | B = Buna-N |
Source: CPU series catalogue, PDF pages 3 and 5. Specification table on page 5.
Where it runs
Condensate polishing in power plants
Condensate polishing in power plants; RO pre-filtration and desalination pretreatment; process and make-up water; paints and coatings, refineries and petrochemicals; microelectronics, resin and fibre filtration.
Clarywound CPU in wound polypropylene at 54 mm OD, nominal rated.

“The increased filtration area results in very low pressure drop and substantially decreased filter change out frequency.”
Resources for this line
Datasheets and catalogue pages that cover Clarypleat CPU, as PDF.
- Clarypleat CPU: filters for power plants0.5 MB · May 2026Download
Related products and tools
Above 82 °C
Kryticalpleat All Fluoropolymer is rated to 160 °C.
View Kryticalpleat All FluoropolymerFiner ratings
Clarypleat NE is available from 5 µm (5 to 100 µm).
View Clarypleat NEChemical compatibility
A fluid checked against membrane, media, seal and housing materials at the operating temperature.
Open checkerHousings
Stainless steel, uPVC, FRP and polypropylene housings, bag vessels and skids.
View housings and systems
Request a quote
Send the part number you use today, the micron rating, flow and fluid. An application engineer replies with the matching Gopani cartridge.
Request a quote- Download the catalogues
The Clarypleat CPU catalogue and the rest of the pleated cartridges range, as PDF.
Go to downloads - Compare the pleated cartridges range
Kryticalpleat PES, Kryticalpleat All Fluoropolymer, Clarypleat PES, Clarypleat PTFE, Clarypleat HE, Clarypleat NE, Clarypleat PVDF, Clarypleat Nylon, Clarypleat 5000
Open the family