Skip to content

Housings and systems

Clary-T Ventis an electropolished vent filter housing, Ra ≤ 0.4 µm. Standard, jacketed or temperature controlled.

Vent filter housings for sterile tank venting, fermentation, pharma, food and beverage and process air and gas. The housings are electropolished and crevice free, designed for low hold-up volume, and made in three types: standard, jacketed, and jacketed with an electronic temperature controller.

Clary-T Vent, catalogue image

-25 to 135 °C

Clary-T Vent 5" to 30" cartridges

Clary-T VentRequest a quote
Internal finish
Ra ≤ 0.4 µm
Temperature
-25 to 135 °C
Pressure rating
-1 to 7 bar
Cartridge lengths
5" to 30"
  • Crevice free

    Electropolished to Ra ≤ 0.4 µm (≤ 15 µinch) on the inside, which removes metal residue left by machining.

  • Jacketed types

    T2 is jacketed; T3 adds an electronic temperature controller.

  • Checked and documented

    Dimensional, weld and surface checks and a hydro test, with documentation to the relevant standard.

  • Quick fit connections

    Quick fit type connections for easy cartridge change-out.

How it is built

Three types: standard, jacketed, jacketed with controller

  1. T1, standard

    A standard vent filter housing.

  2. T2, jacketed

    A jacket around the housing.

  3. T3, jacketed and controlled

    A jacketed housing with an electronic temperature controller: 16 bit, 0.5 s sampling, single set point, IP65 / IP20.

Clary-T Vent, catalogue image
FinishElectropolished, Ra ≤ 0.4 µm
ConnectionsTri-clover, DIN, ASA 150#, 1/4" to 3"
SealsSilicone, EPDM

Specifications

Specification table

MaterialsHousing, clamp, seals

PropertyValue
HousingSS 304, SS 316, SS 316L, duplex SS 2205, duplex SS 2507
Closure clampSS 304
O-ringSilicone, EPDM; others on request

Operating limitsPressure, temperature, finish

PropertyValue
Pressure rating-0.1 to 0.7 MPa (-1.0 to 7.0 bar)
Temperature-25 to +135 °C (-13 to 275 °F)
Internal finishRa ≤ 0.4 µm (≤ 15 µinch)
CartridgeCode-7 (226); 5", 10", 20", 30"; junior housing on request
Inlet and outletTri-clover, DIN flange, ASA 150# flange; 1/4" to 3"; others on request
Drain and ventTri-clover 1/4", 1/2", 3/4", 1"; others on request
Design codecGMP, GEP, ASME Section VIII Division 1, CE marked to PED 97/23/EC

T3 controllerElectronic temperature controller

PropertyValue
RelaySolid state, 25 A / 400 V AC
TypeSingle set point; 16 bit A/D; 0.5 s sampling
Supply and powerSwitch mode power supply; 3 VA
Data backupFlash, 10 years
Electrical connectionMini-Fit Jr. Molex, 6 pin
Bezel and displayBezel 96 × 72 mm; display height 0.36"
ProtectionIP65 / IP20

Ordering codeBuild the part number field by field

PropertyValue
PatternCTVF- + housing type + design code + length + cartridge type + material + connection type + size + drain/vent size + seal
Housing typeT1; T2; T3
Design codeA = ASME Section VIII Division 1; C = CE mark (PED 97/23/EC); G = cGMP
Cartridge length5 = 5"; 1 = 10"; 2 = 20"; 3 = 30"
Cartridge type1 = Fin / 226 (Code-7)
Material6L = SS 316L
Connection typeA = ASA 150# flange; V = tri-clover (V-band); U = DIN flange
Connection size14 = 1/4"; 05 = 1/2"; 34 = 3/4"; 01 = 1"; 15 = 1 1/2"; 02 = 2"; 25 = 2 1/2"; 3 = 3"
Drain / vent size14 = 1/4"; 05 = 1/2"; 34 = 3/4"; 01 = 1"
SealE = EPDM; S = silicone

Source: Clary-T Vent catalogue, 2026, p2 to p5, and the Clary-T SS All Filter Housing catalogue, 2026, p10 to p13.

Where it runs

Sterile tank vents, fermenters and process gas

Applications in the catalogue

Sterile tank vent filtration in biopharmaceutical manufacturing, fermentation systems, pharmaceutical processing, food and beverage production, and process air and gas.

Cartridges to fit

Code-7 hydrophobic vent cartridges such as Clarypleat PTFE, 5" to 30".

“Crevice free electropolished surface with an internal Ra value of ≤ 0.4 μm.”
Clary-T Vent catalogue, 2026
See the catalogues

Resources for this line

Datasheets and catalogue pages that cover Clary-T Vent, as PDF.

  • Clary-T SS filter housings2.1 MB · Sep 2026
    Download
  • Clary-T Vent0.9 MB · Jun 2026
    Download

Open the full library

Related products and tools

  • Above 135 °C

    Fluidizing filters is rated to 600 °C.

    View Fluidizing filters
  • Finer ratings

    Clarypleat HE is available from 0.22 µm (0.22 to 50 µm).

    View Clarypleat HE
  • Chemical compatibility

    A fluid checked against membrane, media, seal and housing materials at the operating temperature.

    Open checker

Request a quote

Send the part number you use today, the micron rating, flow and fluid. An application engineer replies with the matching Gopani cartridge.

Request a quote
  • Download the catalogues

    The Clary-T Vent catalogue and the rest of the housings and systems range, as PDF.

    Go to downloads
  • Compare the housings and systems range

    Clary-T CF, Clary-T SF sanitary housing, Clary-T SF strainer, Clary-T HF, Clary-T BF, Clary-T LF, ClarySEA FRP housing, Polyfilt CF, Polyfilt BF, Polyfilt HF, Plastofilt CF, Plastofilt BF, Catalyst recovery systems

    Open the family

Download a catalogue

Tell us who you are once and every catalogue opens.

By sending this you agree to our Privacy notice.